saw bandpass filter act part no.: act f 8156 _897.5mhz_rf saw_v1.0 product type : customer : saw filter part n o . : customer part n o . : act f 8156 _897.5mhz_rf saw_v1.0 issued date : prepared by checked by approved by
feature s ? low - loss rf filter for mobile systems ? low amplitude ripple ? no m atching network required for operation at 50 ? ceramic p ackage for s urface m ounted t echnology ( smt ) ? lead- free production and rohs c omplian t package dimension s ceramic package: dcc6 c pin configuration 2 input 5 output 1, 3, 4, 6 ground marking top view, laser marking " act ?: manufacturer?s mark ? f ?: saw filter ? 8 15 6 ?: part number ? ?: terminal 1 ??: lot number (the code shown below varies in a 4 - year cycle) code 1 2 3 4 5 6 7 8 9 10 11 12 2010 n p q r s t u v w x y z 2 0 11 a b c d e f g h i j k m 2012 n p q r s t u v w x y z 2013 a b c d e f g h j k l m maximum ratings rating value unit input power level p 13.5 dbm cw ta=85 c life time>10 years 20 dbm cw ta=85 c pass band top frequency test 1000 hours co ntinuously ,electrical characters meet demand 23 dbm cw ta=85 c pass band top frequency test 2 hours continuously ,electrical characters meet demand dc v oltage v dc 12 v operating t emperature r ange t a -40 ~ + 85 c storage t emperature r ange t stg -40 ~ +85 c - 2 -
electrical characteristics parameter unit minimum typical maximum center frequency mhz 897.5 useable bandwidth mhz 35 insertion loss (8 80 ~ 915 mhz) db 2.0 2.3 amplitude variation (8 80 ~ 915 mhz) db 0.8 1. 0 absolute attenuation 0.3 ~ 620 mh z db 40 60 620~ 840 mhz db 45 60 925 ~ 935 mhz db 10 16 935 ~ 960 mhz db 20 30 1200 ~ 1400 mhz db 40 50 1950~ 1990 mhz db 40 45 1990 ~ 2035 mhz db 38 43 3000~ 3400 mhz db 20 23 3400 ~ 50 00mhz db 10 12 input/output vswr (8 80 ~ 915 mhz) db 1.8 rohs c ompli an t electrostatic sensitive device typical frequency response - 3 -
stability c haracteristics test item condition of test 1 mechanical shock (a) drops: 3 times on con crete floor (b) height: 1.0 m 2 vibration resistance (a) frequency of vibration: 10 ~ 55hz (b) amplitude: 1.5 mm (c) directions: x,y and z (d) duration: 2 hours 3 moisture resistance (a) condition: 40 c , 90~95% r.h. (b) durat ion: 96 hours (c) wait 4 hours before measurement 4 climatic sequence (a) + 70c for 16 hours (b) +55 c for 24 hours, 90~95% r.h. (c) -25c for 2 hours (d) +40 c for 24 hours, 90~95% r.h. (e) wait 4 hours before measurement 5 high t emper ature e xposure (a) temperature: 70 c (b) duration: 250 hours (c) wait 4 hours before measurement 6 thermal impact (a) +70 c for 30 minutes ? -25 c for 30 minutes repeated 3 times (b) wait 4 hours before measurement requirements : the saw filer shall remain w ithin the electrical specifications after tests. remarks ? saw devices should not be used in any type of fluid such as water, oil, organic solvent, etc. ? be certain not to apply voltage exceeding the rated voltage of components. ? do n ot operate outside the recommended operating temperature range of components. ? sudden change of temperature shall be avoided, deterioration of the characteristics can occur. ? be careful of soldering temperature and duration of components when soldering. ? do n ot place soldering iron on the body of components. ? be careful not to subject the terminals or leads of components to excessive force. - 4 -
? saw devices are electrostatic sensitive . p lease avoid static voltage during operation and storage. ? u ltrasonic cleaning shall be avoided . ultrasonic vibration may ca use destruction of components . test circuit recommended land pattern r ecommended soldering profile - 5 -
packing information carrier tape reel dimensions outer packing type quantity dimens ion description weight carton box 0.85 carton box 2 0000 190190190 1. 8 0 unit: mm unit: kg c e a act 201 1 . all rights reserved. 1. the spec ifications of this device are subject to change or obsolescence without notice. 2. typically, equipment utilizing this device requires emissions testing and government approval, which is the responsibility of the equipment manufacturer. 3. our liability is only assumed for the surface acoustic wave (saw) component(s) per se, not for applications, processes and circuits implemented within components or assemblies. - 6 -
|
